CONFAST 1/4" x 2-1/4" Blue Flat Phillips Concrete Screw Anchor with Drill Bit for Anchoring to Masonry, Block or Brick (100 per Box)
Produktdetails
| Artikelnummer | 218079969 | Erscheinungsdatum | 2026/05/03 | Listenpreis | €11.96 | Modellnummer | 218079969 | ||
|---|---|---|---|---|---|---|---|---|---|
| Kategorie | |||||||||
ApplicationsThe anchor is made from Carbon Steel, and is Blue. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Dry environment.Head Style The anchor is a Flat Countersunk Phillips head and is designed to prevent the head from protruding above the surface of the item being attached.Hole Diameter/Bit DiameterThe anchor requires a 3/16" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Driver RequiredA #3 phillips bit is required for driving the anchor into the base material.Diameter of Anchor The diameter of the anchor is 1/4".Length Anchor The length of the anchor is 2-1/4"Thread LengthThe length of the threads on the anchor is 1-3/4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3/4" to 1-1/4". This will ensure that the minimum embedment of 1" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".Spacing between AnchorsEach anchor must be spaced a minimum distance of 4" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
- BIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost
- FLAT PHILLIPS HEAD--Can be driven with Phillips Screw Driver
- SELF-TAPPING-Taps threads directly into masonry and requires no other anchor
- DIAMOND POINT-Easier to drive the screw to save time
| UPC | 820274000021 |
|---|---|
| Brand | CONFAST |
| Head Type | Flat |
| Size Name | 1/4" x 2-1/4" |
| Metal Type | Carbon Steel |
| Unit Count | 100 Count |
| Item Weight | 1 Pounds |
| Part Number | CSF14214 |
| Thread Size | 1/4 inch |
| Thread Type | Un |
| Drive System | Phillips |
| Manufacturer | CONFAST |
| Thread Class | Full |
| Thread Style | Self-Tapping |
| Fastener Size | 1/4 x 2-1/4 inches |
| Fastener Type | self-tapping-taps |
| Item Diameter | 0.25 Inches |
| Material Type | Carbon Steel - Blue Coated |
| Exterior Finish | Alloy Steel |
| Number Of Items | 100 |
| Thread Coverage | Partially Threaded |
| Number of Pieces | 100 |
| Screw Head Style | Flat Countersunk Phillips |
| Screw Point Style | diamond point-easier |
| Maximum Shear Strength | 675 |
| Compatible Groove Diameter | 0.16 Inches |
Korrektur der Produktinformationen
Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.
Korrekturanfrage